This pack combines many case histories regarding the LabTecta product range. Detailing return on investment and increases in mean time between failure.
Related Products Pages
IP66 certified designs that conform to IEEE Std. 841-2021
Labtecta Key Case Studies
Featured Case Studies
The case studies below showcase the very best of commitment to excellence at AESSEAL across our three core pillars:
- Exceptional Customer Service – putting customers first, every time.
- Advanced Technology – delivering innovation that drives results.
- Sustainable Solutions – engineering a better future for people and our planet.
Annual savings of over $2.6 million
A food and beverage customer was experiencing high leakage and contamination in their process fluid on the single pass flow through system they were operating.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
ROI In Less Than A Month
a French cardboard manufacturer was experiencing seal failures every two months. AESSEAL worked closely with the customer to find the right solution.
AESSEAL product stops hot oil pump leakage
A large oil and gas company in north Africa contacted AESSEAL to look at a sealing issue on its hot oil pumps.
CDPH & EasyClean boosts MTBF from four months to seven years
The installation of a CDPH double mechanical seal along with an EasyClean™ seal support system proved to be the remedy for the frequent failures of a competitor’s seal at a power plant in Denmark.
Prompt delivery saves three-month delay
A 12-week delay on the commissioning of a new oil and gas plant in Kuwait was avoided when AESSEAL was able to step in to replace a defective competitor’s seal at short notice.
AES-Elast the answer to seal selection problem
Employees at William Grant’s Scottish whisky distillery in Girvan, Ayshire, were having difficulty selecting the correct mechanical seals for specific applications.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
Major savings follow installation of AESSEAL product
A petrochemical company based in the Middle East was having problems with persistent and costly seal failures.
Seal upgrades save over US $3.4million in seven years
A company in the Oil and Gas industry in Qatar were dissatisfied with the reliability of the mechanical seal used in crude export and oil/water booster pumps.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
Improved Safety and Reliability
A major manufacturer in the UK were having reliability issues with the seal on a critical Labour chemical pump used to pump caustic solution.
DMSF seal the answer at South African plant
The installation of the AESSEAL DMSF seal and SW2 water management system at the Ford plant in Pretoria, South Africa, has improved the MTBF of a crucial seal from less than two weeks to more than two years.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
Improved reliability for new process
A refinery in Canada were commissioning a new lipids coprocessing initiative where renewable feedstock is injected into the cracker.
DMSF seal the answer at South African plant
The installation of the AESSEAL DMSF seal and SW2 water management system at the Ford plant in Pretoria, South Africa, has improved the MTBF of a crucial seal from less than two weeks to more than two years.
AESSEAL helps UK firm to multi-million pound savings
A leading UK company is set to save more than £5 million over five years following the installation of AESSEAL LabTecta OP bearing protectors.
Change to packing saves Swiss company $millions
A chocolate producer in Switzerland has saved around ₣2.3 million ($2.6 million) over the past year following its decision to change to an AESSEAL pump packing system.
DMSF solves reliability issues for Swedish company
Elastomer degradation was causing the seals on three of the boiler feed pumps at a Swedish energy plant to fail around every 12 months.
Improved Safety and Reliability
A major manufacturer in the UK were having reliability issues with the seal on a critical Labour chemical pump used to pump caustic solution.
Staying cool in Cardiff
The cooling system in a High Profile office building in the Cardiff Bay area was operating with just a single duty pump and no standby.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
Staying cool in Cardiff
The cooling system in a High Profile office building in the Cardiff Bay area was operating with just a single duty pump and no standby.
AES-Elast the answer to seal selection problem
Employees at William Grant’s Scottish whisky distillery in Girvan, Ayshire, were having difficulty selecting the correct mechanical seals for specific applications.
Standard of service makes AESSEAL a clear winner
The seal on a pump at a chemical plant in the east of England was burning out on average every two weeks due to dry running, resulting in some four hours of downtime each time it failed.
Mining company saves $8 million AUD with AESSEAL system
A coal mine in Australia was having seal failures roughly every two weeks on two disposal pumps.
Chemical plant saved over €500,000 in the first year
A critical glue agitator vessel was affecting productivity for a silicone manufacturing facility in France. This situation was costing the company thousands of Euros in lost production.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
Reliability Improved For Waste Energy Company
Enfinium were disappointed with the support provided by their pump OEM
Standard of service makes AESSEAL a clear winner
The seal on a pump at a chemical plant in the east of England was burning out on average every two weeks due to dry running, resulting in some four hours of downtime each time it failed.
Fantastic seal life for notoriously difficult application
A pulp & paper company in the Canada were dissatisfied with the reliability of the mechanical seal used in its Chlorine Dioxide generator pump.
AESSEAL product stops hot oil pump leakage
A large oil and gas company in north Africa contacted AESSEAL to look at a sealing issue on its hot oil pumps.
80 million litres of water per year to be saved at Mexican mine
The Grupo Mexico Caridad mine in Mexico was experiencing lengthy downtimes and using high volumes of water for lubricating pump packing.
Chemical Producer Saves Over £1.7 Million in Plant Downtime
A specialty chemical company at its UK processing facility were desperately trying to get spare parts for the mechanical seal on one of its critical reactors.
AESSEAL help a Polyethylene plant save €144,000 in 30 months
Replacing labyrinth seals with MagTecta on 8 lobe blowers increases MTBF to over 400%.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
AESSEAL product removes risk of HFC emissions
A specially designed double seal from AESSEAL has enabled an Italian drinks company to avoid the risk of major financial penalties which could have resulted from the release into the atmosphere of highly damaging HFC (hydrofluorocarbon) gases.
Reliability Improved For Waste Energy Company
Enfinium were disappointed with the support provided by their pump OEM
Mechanical seals runs an incredible 17 years without problems
Tongaat Hullett Sugar were un happy with the amount of maintenance required on the sealing of one of its pumps.
DMSF seal the answer at South African plant
The installation of the AESSEAL DMSF seal and SW2 water management system at the Ford plant in Pretoria, South Africa, has improved the MTBF of a crucial seal from less than two weeks to more than two years.
80 million litres of water per year to be saved at Mexican mine
The Grupo Mexico Caridad mine in Mexico was experiencing lengthy downtimes and using high volumes of water for lubricating pump packing.
ROI In Less Than A Month
a French cardboard manufacturer was experiencing seal failures every two months. AESSEAL worked closely with the customer to find the right solution.
AESSEAL help a Polyethylene plant save €144,000 in 30 months
Replacing labyrinth seals with MagTecta on 8 lobe blowers increases MTBF to over 400%.
Warman conversion the answer for Spanish company
A seal conversion kit for the Warman® AH Range of Ultra Heavy Duty Slurry Pumps helped to solve a variety of problems being experienced by a Spanish aluminium producer.
Annual savings of over $2.6 million
A food and beverage customer was experiencing high leakage and contamination in their process fluid on the single pass flow through system they were operating.
80 million litres of water per year to be saved at Mexican mine
The Grupo Mexico Caridad mine in Mexico was experiencing lengthy downtimes and using high volumes of water for lubricating pump packing.
ROI In Less Than A Month
a French cardboard manufacturer was experiencing seal failures every two months. AESSEAL worked closely with the customer to find the right solution.
AESSEAL help a Polyethylene plant save €144,000 in 30 months
Replacing labyrinth seals with MagTecta on 8 lobe blowers increases MTBF to over 400%.
Warman conversion the answer for Spanish company
A seal conversion kit for the Warman® AH Range of Ultra Heavy Duty Slurry Pumps helped to solve a variety of problems being experienced by a Spanish aluminium producer.
80 million litres of water per year to be saved at Mexican mine
The Grupo Mexico Caridad mine in Mexico was experiencing lengthy downtimes and using high volumes of water for lubricating pump packing.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
DMSF seal the answer at South African plant
The installation of the AESSEAL DMSF seal and SW2 water management system at the Ford plant in Pretoria, South Africa, has improved the MTBF of a crucial seal from less than two weeks to more than two years.
Change to packing saves Swiss company $millions
A chocolate producer in Switzerland has saved around ₣2.3 million ($2.6 million) over the past year following its decision to change to an AESSEAL pump packing system.
Warman conversion the answer for Spanish company
A seal conversion kit for the Warman® AH Range of Ultra Heavy Duty Slurry Pumps helped to solve a variety of problems being experienced by a Spanish aluminium producer.
Major savings for Algerian food producer
A food production plant in Algeria is saving an estimated $225,000 a year following the installation of an AESSEAL LabTecta OP bearing protector.
Staying cool in Cardiff
The cooling system in a High Profile office building in the Cardiff Bay area was operating with just a single duty pump and no standby.
Full steam ahead for refinery after change to STS seals
An oil and gas refinery in northern England was experiencing poor reliability of its steam turbine.
Fantastic seal life for notoriously difficult application
A pulp & paper company in the Canada were dissatisfied with the reliability of the mechanical seal used in its Chlorine Dioxide generator pump.
CDPH & EasyClean boosts MTBF from four months to seven years
The installation of a CDPH double mechanical seal along with an EasyClean™ seal support system proved to be the remedy for the frequent failures of a competitor’s seal at a power plant in Denmark.
DMSF makes its mark in Japanese paper industry
The installation of an AESSEAL® DMSF™ seal at a Japanese paper plant has increased the MTBF from just six months to seven years.
Chemical Producer Saves Over £1.7 Million in Plant Downtime
A specialty chemical company at its UK processing facility were desperately trying to get spare parts for the mechanical seal on one of its critical reactors.
DMSF seal the answer at South African plant
The installation of the AESSEAL DMSF seal and SW2 water management system at the Ford plant in Pretoria, South Africa, has improved the MTBF of a crucial seal from less than two weeks to more than two years.
CDPH & EasyClean boosts MTBF from four months to seven years
The installation of a CDPH double mechanical seal along with an EasyClean™ seal support system proved to be the remedy for the frequent failures of a competitor’s seal at a power plant in Denmark.
AESSEAL helps UK firm to multi-million pound savings
A leading UK company is set to save more than £5 million over five years following the installation of AESSEAL LabTecta OP bearing protectors.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
AESSEAL product stops hot oil pump leakage
A large oil and gas company in north Africa contacted AESSEAL to look at a sealing issue on its hot oil pumps.
Improved Safety and Reliability
A major manufacturer in the UK were having reliability issues with the seal on a critical Labour chemical pump used to pump caustic solution.
AESSEAL product stops hot oil pump leakage
A large oil and gas company in north Africa contacted AESSEAL to look at a sealing issue on its hot oil pumps.
Chemical plant saved over €500,000 in the first year
A critical glue agitator vessel was affecting productivity for a silicone manufacturing facility in France. This situation was costing the company thousands of Euros in lost production.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
Warman conversion the answer for Spanish company
A seal conversion kit for the Warman® AH Range of Ultra Heavy Duty Slurry Pumps helped to solve a variety of problems being experienced by a Spanish aluminium producer.
Staying cool in Cardiff
The cooling system in a High Profile office building in the Cardiff Bay area was operating with just a single duty pump and no standby.
Warman conversion the answer for Spanish company
A seal conversion kit for the Warman® AH Range of Ultra Heavy Duty Slurry Pumps helped to solve a variety of problems being experienced by a Spanish aluminium producer.
ROI In Less Than A Month
a French cardboard manufacturer was experiencing seal failures every two months. AESSEAL worked closely with the customer to find the right solution.
Warman conversion the answer for Spanish company
A seal conversion kit for the Warman® AH Range of Ultra Heavy Duty Slurry Pumps helped to solve a variety of problems being experienced by a Spanish aluminium producer.
CDPH & EasyClean boosts MTBF from four months to seven years
The installation of a CDPH double mechanical seal along with an EasyClean™ seal support system proved to be the remedy for the frequent failures of a competitor’s seal at a power plant in Denmark.
DMSF seal the answer at South African plant
The installation of the AESSEAL DMSF seal and SW2 water management system at the Ford plant in Pretoria, South Africa, has improved the MTBF of a crucial seal from less than two weeks to more than two years.
Mechanical seals runs an incredible 17 years without problems
Tongaat Hullett Sugar were un happy with the amount of maintenance required on the sealing of one of its pumps.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
Prompt delivery saves three-month delay
A 12-week delay on the commissioning of a new oil and gas plant in Kuwait was avoided when AESSEAL was able to step in to replace a defective competitor’s seal at short notice.
Standard of service makes AESSEAL a clear winner
The seal on a pump at a chemical plant in the east of England was burning out on average every two weeks due to dry running, resulting in some four hours of downtime each time it failed.
New approach for slurry pumps reduces water usage by 95%
A copper mining company in central Africa was encountering problems of excessive water usage
Major savings follow installation of AESSEAL product
A petrochemical company based in the Middle East was having problems with persistent and costly seal failures.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
Change to packing saves Swiss company $millions
A chocolate producer in Switzerland has saved around ₣2.3 million ($2.6 million) over the past year following its decision to change to an AESSEAL pump packing system.
CDPH & EasyClean boosts MTBF from four months to seven years
The installation of a CDPH double mechanical seal along with an EasyClean™ seal support system proved to be the remedy for the frequent failures of a competitor’s seal at a power plant in Denmark.
Safety and reliability with AESSEAL heavy duty seal
A mining company in Australia was facing persistent problems from seal failures on one of its slurry pumps.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
DMSF makes its mark in Japanese paper industry
The installation of an AESSEAL® DMSF™ seal at a Japanese paper plant has increased the MTBF from just six months to seven years.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
DMSF seal the answer at South African plant
The installation of the AESSEAL DMSF seal and SW2 water management system at the Ford plant in Pretoria, South Africa, has improved the MTBF of a crucial seal from less than two weeks to more than two years.
Standard of service makes AESSEAL a clear winner
The seal on a pump at a chemical plant in the east of England was burning out on average every two weeks due to dry running, resulting in some four hours of downtime each time it failed.
Chemical plant saved over €500,000 in the first year
A critical glue agitator vessel was affecting productivity for a silicone manufacturing facility in France. This situation was costing the company thousands of Euros in lost production.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
Change to packing saves Swiss company $millions
A chocolate producer in Switzerland has saved around ₣2.3 million ($2.6 million) over the past year following its decision to change to an AESSEAL pump packing system.
AESSEAL product stops hot oil pump leakage
A large oil and gas company in north Africa contacted AESSEAL to look at a sealing issue on its hot oil pumps.
Safety and reliability with AESSEAL heavy duty seal
A mining company in Australia was facing persistent problems from seal failures on one of its slurry pumps.
Staying cool in Cardiff
The cooling system in a High Profile office building in the Cardiff Bay area was operating with just a single duty pump and no standby.
AESSEAL help a Polyethylene plant save €144,000 in 30 months
Replacing labyrinth seals with MagTecta on 8 lobe blowers increases MTBF to over 400%.
AESSEAL system fixes sewage problems for US township
A municipality in Pennsylvania was having issues with major inefficiencies in its sewage treatment system.
ROI In Less Than A Month
a French cardboard manufacturer was experiencing seal failures every two months. AESSEAL worked closely with the customer to find the right solution.
Major savings follow installation of AESSEAL product
A petrochemical company based in the Middle East was having problems with persistent and costly seal failures.
Warman conversion the answer for Spanish company
A seal conversion kit for the Warman® AH Range of Ultra Heavy Duty Slurry Pumps helped to solve a variety of problems being experienced by a Spanish aluminium producer.
ROI In Less Than A Month
a French cardboard manufacturer was experiencing seal failures every two months. AESSEAL worked closely with the customer to find the right solution.
Warman conversion the answer for Spanish company
A seal conversion kit for the Warman® AH Range of Ultra Heavy Duty Slurry Pumps helped to solve a variety of problems being experienced by a Spanish aluminium producer.
Fantastic seal life for notoriously difficult application
A pulp & paper company in the Canada were dissatisfied with the reliability of the mechanical seal used in its Chlorine Dioxide generator pump.
Chemical plant saved over €500,000 in the first year
A critical glue agitator vessel was affecting productivity for a silicone manufacturing facility in France. This situation was costing the company thousands of Euros in lost production.
AESSEAL system fixes sewage problems for US township
A municipality in Pennsylvania was having issues with major inefficiencies in its sewage treatment system.
Annual savings of over $2.6 million
A food and beverage customer was experiencing high leakage and contamination in their process fluid on the single pass flow through system they were operating.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
CDPH & EasyClean boosts MTBF from four months to seven years
The installation of a CDPH double mechanical seal along with an EasyClean™ seal support system proved to be the remedy for the frequent failures of a competitor’s seal at a power plant in Denmark.
AESSEAL helps UK firm to multi-million pound savings
A leading UK company is set to save more than £5 million over five years following the installation of AESSEAL LabTecta OP bearing protectors.
DMSF seal the answer at South African plant
The installation of the AESSEAL DMSF seal and SW2 water management system at the Ford plant in Pretoria, South Africa, has improved the MTBF of a crucial seal from less than two weeks to more than two years.
Standard of service makes AESSEAL a clear winner
The seal on a pump at a chemical plant in the east of England was burning out on average every two weeks due to dry running, resulting in some four hours of downtime each time it failed.
Bitumen pump upgrade saves over £23,000 a year
Asphalt producer pump for road surfaces was gland packed and losing over 15 tonnes of bitumen.
Staying cool in Cardiff
The cooling system in a High Profile office building in the Cardiff Bay area was operating with just a single duty pump and no standby.
DMSF solves reliability issues for Swedish company
Elastomer degradation was causing the seals on three of the boiler feed pumps at a Swedish energy plant to fail around every 12 months.
Chemical plant saved over €500,000 in the first year
A critical glue agitator vessel was affecting productivity for a silicone manufacturing facility in France. This situation was costing the company thousands of Euros in lost production.
Mechanical seals runs an incredible 17 years without problems
Tongaat Hullett Sugar were un happy with the amount of maintenance required on the sealing of one of its pumps.
Annual savings of over $2.6 million
A food and beverage customer was experiencing high leakage and contamination in their process fluid on the single pass flow through system they were operating.
Standard of service makes AESSEAL a clear winner
The seal on a pump at a chemical plant in the east of England was burning out on average every two weeks due to dry running, resulting in some four hours of downtime each time it failed.
Major savings follow installation of AESSEAL product
A petrochemical company based in the Middle East was having problems with persistent and costly seal failures.
Chemical plant saved over €500,000 in the first year
A critical glue agitator vessel was affecting productivity for a silicone manufacturing facility in France. This situation was costing the company thousands of Euros in lost production.
LabTecta ends dust pollution problem for SA firm
Preventing dust from escaping into the working environment and is saving thousands of dollars a year
AESSEAL system fixes sewage problems for US township
A municipality in Pennsylvania was having issues with major inefficiencies in its sewage treatment system.
AESSEAL helps UK firm to multi-million pound savings
A leading UK company is set to save more than £5 million over five years following the installation of AESSEAL LabTecta OP bearing protectors.
AESSEAL product stops hot oil pump leakage
A large oil and gas company in north Africa contacted AESSEAL to look at a sealing issue on its hot oil pumps.
ROI In Less Than A Month
a French cardboard manufacturer was experiencing seal failures every two months. AESSEAL worked closely with the customer to find the right solution.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
CDPH & EasyClean boosts MTBF from four months to seven years
The installation of a CDPH double mechanical seal along with an EasyClean™ seal support system proved to be the remedy for the frequent failures of a competitor’s seal at a power plant in Denmark.
DMSF solves reliability issues for Swedish company
Elastomer degradation was causing the seals on three of the boiler feed pumps at a Swedish energy plant to fail around every 12 months.
AES-Elast the answer to seal selection problem
Employees at William Grant’s Scottish whisky distillery in Girvan, Ayshire, were having difficulty selecting the correct mechanical seals for specific applications.
Safety and reliability with AESSEAL heavy duty seal
A mining company in Australia was facing persistent problems from seal failures on one of its slurry pumps.
CDPH & EasyClean boosts MTBF from four months to seven years
The installation of a CDPH double mechanical seal along with an EasyClean™ seal support system proved to be the remedy for the frequent failures of a competitor’s seal at a power plant in Denmark.
AESSEAL product brings big savings for South African company
The installation of an AESSEAL FGDSS-N single slurry seal is saving a South African mining company thousands of dollars a year in repair and maintenance costs.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
Prompt delivery saves three-month delay
A 12-week delay on the commissioning of a new oil and gas plant in Kuwait was avoided when AESSEAL was able to step in to replace a defective competitor’s seal at short notice.
AES-Elast the answer to seal selection problem
Employees at William Grant’s Scottish whisky distillery in Girvan, Ayshire, were having difficulty selecting the correct mechanical seals for specific applications.
80 million litres of water per year to be saved at Mexican mine
The Grupo Mexico Caridad mine in Mexico was experiencing lengthy downtimes and using high volumes of water for lubricating pump packing.
AESSEAL upgrade removes safety risk
A sealant being used on an Sulzer APP3 pump by a Spanish biofuel company was leaking each time the pump was stopped.
Change to packing saves Swiss company $millions
A chocolate producer in Switzerland has saved around ₣2.3 million ($2.6 million) over the past year following its decision to change to an AESSEAL pump packing system.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
Staying cool in Cardiff
The cooling system in a High Profile office building in the Cardiff Bay area was operating with just a single duty pump and no standby.
DMSC saves Nestlé Purina £182k in just 10 months
Significant savings with mechanical seal and bearing protection for the pet food manufacturer
Chemical plant saved over €500,000 in the first year
A critical glue agitator vessel was affecting productivity for a silicone manufacturing facility in France. This situation was costing the company thousands of Euros in lost production.
AESSEAL upgrade removes safety risk
A sealant being used on an Sulzer APP3 pump by a Spanish biofuel company was leaking each time the pump was stopped.
DMSC saves Nestlé Purina £182k in just 10 months
Significant savings with mechanical seal and bearing protection for the pet food manufacturer
Warman conversion the answer for Spanish company
A seal conversion kit for the Warman® AH Range of Ultra Heavy Duty Slurry Pumps helped to solve a variety of problems being experienced by a Spanish aluminium producer.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
AESSEAL product stops hot oil pump leakage
A large oil and gas company in north Africa contacted AESSEAL to look at a sealing issue on its hot oil pumps.
Chemical Producer Saves Over £1.7 Million in Plant Downtime
A specialty chemical company at its UK processing facility were desperately trying to get spare parts for the mechanical seal on one of its critical reactors.
AESSEAL upgrade removes safety risk
A sealant being used on an Sulzer APP3 pump by a Spanish biofuel company was leaking each time the pump was stopped.
AESSEAL help a Polyethylene plant save €144,000 in 30 months
Replacing labyrinth seals with MagTecta on 8 lobe blowers increases MTBF to over 400%.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
AESSEAL upgrade removes safety risk
A sealant being used on an Sulzer APP3 pump by a Spanish biofuel company was leaking each time the pump was stopped.
AESSEAL product stops hot oil pump leakage
A large oil and gas company in north Africa contacted AESSEAL to look at a sealing issue on its hot oil pumps.
Seal upgrades save over US $3.4million in seven years
A company in the Oil and Gas industry in Qatar were dissatisfied with the reliability of the mechanical seal used in crude export and oil/water booster pumps.
Bitumen pump upgrade saves over £23,000 a year
Asphalt producer pump for road surfaces was gland packed and losing over 15 tonnes of bitumen.
AESSEAL help a Polyethylene plant save €144,000 in 30 months
Replacing labyrinth seals with MagTecta on 8 lobe blowers increases MTBF to over 400%.
Bitumen pump upgrade saves over £23,000 a year
Asphalt producer pump for road surfaces was gland packed and losing over 15 tonnes of bitumen.
FIDC ends costly leaks at US firm
The installation of an FIDC seal to replace single seals with no flush or API Plan has dramatically improved pump reliability at a pulp and paper company in New England.
Leakage problem solved with STS
A global energy company was facing significant losses as a result of damage to the steam turbine housing at one of its ethylene plants.
Chemical plant saved over €500,000 in the first year
A critical glue agitator vessel was affecting productivity for a silicone manufacturing facility in France. This situation was costing the company thousands of Euros in lost production.
DMSF seal the answer at South African plant
The installation of the AESSEAL DMSF seal and SW2 water management system at the Ford plant in Pretoria, South Africa, has improved the MTBF of a crucial seal from less than two weeks to more than two years.
Seal upgrades save over US $3.4million in seven years
A company in the Oil and Gas industry in Qatar were dissatisfied with the reliability of the mechanical seal used in crude export and oil/water booster pumps.
80 million litres of water per year to be saved at Mexican mine
The Grupo Mexico Caridad mine in Mexico was experiencing lengthy downtimes and using high volumes of water for lubricating pump packing.
CDPH & EasyClean boosts MTBF from four months to seven years
The installation of a CDPH double mechanical seal along with an EasyClean™ seal support system proved to be the remedy for the frequent failures of a competitor’s seal at a power plant in Denmark.
DMSF makes its mark in Japanese paper industry
The installation of an AESSEAL® DMSF™ seal at a Japanese paper plant has increased the MTBF from just six months to seven years.
LabTecta FS the answer for gearbox problem
A repair and maintenance company in West Virginia says that its customers in the local coal mining industry have recorded major savings following a decision to upgrade to AESSEAL LabTecta FS.
Upgrade will result in major savings for US company
A US petrochemical company is set to save tens of thousands of dollars a year following the installation of specially-designed seal pots to replace 40 existing pots which had been in place for around half a century.
Mechanical seals runs an incredible 17 years without problems
Tongaat Hullett Sugar were un happy with the amount of maintenance required on the sealing of one of its pumps.
ROI In Less Than A Month
a French cardboard manufacturer was experiencing seal failures every two months. AESSEAL worked closely with the customer to find the right solution.
Mechanical seals runs an incredible 17 years without problems
Tongaat Hullett Sugar were un happy with the amount of maintenance required on the sealing of one of its pumps.
Annual savings of over $2.6 million
A food and beverage customer was experiencing high leakage and contamination in their process fluid on the single pass flow through system they were operating.
Standard of service makes AESSEAL a clear winner
The seal on a pump at a chemical plant in the east of England was burning out on average every two weeks due to dry running, resulting in some four hours of downtime each time it failed.
AESSEAL product stops hot oil pump leakage
A large oil and gas company in north Africa contacted AESSEAL to look at a sealing issue on its hot oil pumps.
Chemical plant saved over €500,000 in the first year
A critical glue agitator vessel was affecting productivity for a silicone manufacturing facility in France. This situation was costing the company thousands of Euros in lost production.
Prompt delivery saves three-month delay
A 12-week delay on the commissioning of a new oil and gas plant in Kuwait was avoided when AESSEAL was able to step in to replace a defective competitor’s seal at short notice.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
Chemical Producer Saves Over £1.7 Million in Plant Downtime
A specialty chemical company at its UK processing facility were desperately trying to get spare parts for the mechanical seal on one of its critical reactors.
AESSEAL helps UK firm to multi-million pound savings
A leading UK company is set to save more than £5 million over five years following the installation of AESSEAL LabTecta OP bearing protectors.
Standard of service makes AESSEAL a clear winner
The seal on a pump at a chemical plant in the east of England was burning out on average every two weeks due to dry running, resulting in some four hours of downtime each time it failed.
ROI In Less Than A Month
a French cardboard manufacturer was experiencing seal failures every two months. AESSEAL worked closely with the customer to find the right solution.
AESSEAL product stops hot oil pump leakage
A large oil and gas company in north Africa contacted AESSEAL to look at a sealing issue on its hot oil pumps.
AESSEAL product stops hot oil pump leakage
A large oil and gas company in north Africa contacted AESSEAL to look at a sealing issue on its hot oil pumps.
Seal upgrades save over US $3.4million in seven years
A company in the Oil and Gas industry in Qatar were dissatisfied with the reliability of the mechanical seal used in crude export and oil/water booster pumps.
Annual savings of over $2.6 million
A food and beverage customer was experiencing high leakage and contamination in their process fluid on the single pass flow through system they were operating.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
Major savings with CKD double seal
The single seals being used by Swedish water treatment company were unsuitable for the job they were being asked to do, allowing limescale to enter between the seal faces and leak out on to the floor of the plant.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
ROI In Less Than A Month
a French cardboard manufacturer was experiencing seal failures every two months. AESSEAL worked closely with the customer to find the right solution.
Annual savings of over $2.6 million
A food and beverage customer was experiencing high leakage and contamination in their process fluid on the single pass flow through system they were operating.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
AESSEAL upgrade removes safety risk
A sealant being used on an Sulzer APP3 pump by a Spanish biofuel company was leaking each time the pump was stopped.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
Prompt delivery saves three-month delay
A 12-week delay on the commissioning of a new oil and gas plant in Kuwait was avoided when AESSEAL was able to step in to replace a defective competitor’s seal at short notice.
Full steam ahead for refinery after change to STS seals
An oil and gas refinery in northern England was experiencing poor reliability of its steam turbine.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
Mechanical seals runs an incredible 17 years without problems
Tongaat Hullett Sugar were un happy with the amount of maintenance required on the sealing of one of its pumps.
DMSF seal the answer at South African plant
The installation of the AESSEAL DMSF seal and SW2 water management system at the Ford plant in Pretoria, South Africa, has improved the MTBF of a crucial seal from less than two weeks to more than two years.
DMSF seal the answer at South African plant
The installation of the AESSEAL DMSF seal and SW2 water management system at the Ford plant in Pretoria, South Africa, has improved the MTBF of a crucial seal from less than two weeks to more than two years.
AESSEAL product stops hot oil pump leakage
A large oil and gas company in north Africa contacted AESSEAL to look at a sealing issue on its hot oil pumps.
CDPH & EasyClean boosts MTBF from four months to seven years
The installation of a CDPH double mechanical seal along with an EasyClean™ seal support system proved to be the remedy for the frequent failures of a competitor’s seal at a power plant in Denmark.
Mining company saves $8 million AUD with AESSEAL system
A coal mine in Australia was having seal failures roughly every two weeks on two disposal pumps.
Mining company saves $8 million AUD with AESSEAL system
A coal mine in Australia was having seal failures roughly every two weeks on two disposal pumps.
DMSC saves Nestlé Purina £182k in just 10 months
Significant savings with mechanical seal and bearing protection for the pet food manufacturer
CDPH & EasyClean boosts MTBF from four months to seven years
The installation of a CDPH double mechanical seal along with an EasyClean™ seal support system proved to be the remedy for the frequent failures of a competitor’s seal at a power plant in Denmark.
Improved reliability for new process
A refinery in Canada were commissioning a new lipids coprocessing initiative where renewable feedstock is injected into the cracker.
Fantastic seal life for notoriously difficult application
A pulp & paper company in the Canada were dissatisfied with the reliability of the mechanical seal used in its Chlorine Dioxide generator pump.
DMSF solves reliability issues for Swedish company
Elastomer degradation was causing the seals on three of the boiler feed pumps at a Swedish energy plant to fail around every 12 months.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
AESSEAL product stops hot oil pump leakage
A large oil and gas company in north Africa contacted AESSEAL to look at a sealing issue on its hot oil pumps.
Fantastic seal life for notoriously difficult application
A pulp & paper company in the Canada were dissatisfied with the reliability of the mechanical seal used in its Chlorine Dioxide generator pump.
Mining company saves $8 million AUD with AESSEAL system
A coal mine in Australia was having seal failures roughly every two weeks on two disposal pumps.
AESSEAL upgrade removes safety risk
A sealant being used on an Sulzer APP3 pump by a Spanish biofuel company was leaking each time the pump was stopped.
Major savings for Algerian food producer
A food production plant in Algeria is saving an estimated $225,000 a year following the installation of an AESSEAL LabTecta OP bearing protector.
Chemical Producer Saves Over £1.7 Million in Plant Downtime
A specialty chemical company at its UK processing facility were desperately trying to get spare parts for the mechanical seal on one of its critical reactors.
Safety and reliability with AESSEAL heavy duty seal
A mining company in Australia was facing persistent problems from seal failures on one of its slurry pumps.
Bitumen pump upgrade saves over £23,000 a year
Asphalt producer pump for road surfaces was gland packed and losing over 15 tonnes of bitumen.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
Fantastic seal life for notoriously difficult application
A pulp & paper company in the Canada were dissatisfied with the reliability of the mechanical seal used in its Chlorine Dioxide generator pump.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
AESSEAL system fixes sewage problems for US township
A municipality in Pennsylvania was having issues with major inefficiencies in its sewage treatment system.
DMSF makes its mark in Japanese paper industry
The installation of an AESSEAL® DMSF™ seal at a Japanese paper plant has increased the MTBF from just six months to seven years.
DMSC saves Nestlé Purina £182k in just 10 months
Significant savings with mechanical seal and bearing protection for the pet food manufacturer
Change to packing saves Swiss company $millions
A chocolate producer in Switzerland has saved around ₣2.3 million ($2.6 million) over the past year following its decision to change to an AESSEAL pump packing system.
DMSF solves reliability issues for Swedish company
Elastomer degradation was causing the seals on three of the boiler feed pumps at a Swedish energy plant to fail around every 12 months.
DMSF seal the answer at South African plant
The installation of the AESSEAL DMSF seal and SW2 water management system at the Ford plant in Pretoria, South Africa, has improved the MTBF of a crucial seal from less than two weeks to more than two years.
Warman conversion the answer for Spanish company
A seal conversion kit for the Warman® AH Range of Ultra Heavy Duty Slurry Pumps helped to solve a variety of problems being experienced by a Spanish aluminium producer.
Chemical plant saved over €500,000 in the first year
A critical glue agitator vessel was affecting productivity for a silicone manufacturing facility in France. This situation was costing the company thousands of Euros in lost production.
Fantastic seal life for notoriously difficult application
A pulp & paper company in the Canada were dissatisfied with the reliability of the mechanical seal used in its Chlorine Dioxide generator pump.
ROI In Less Than A Month
a French cardboard manufacturer was experiencing seal failures every two months. AESSEAL worked closely with the customer to find the right solution.
AESSEAL system fixes sewage problems for US township
A municipality in Pennsylvania was having issues with major inefficiencies in its sewage treatment system.
Chemical plant saved over €500,000 in the first year
A critical glue agitator vessel was affecting productivity for a silicone manufacturing facility in France. This situation was costing the company thousands of Euros in lost production.
80 million litres of water per year to be saved at Mexican mine
The Grupo Mexico Caridad mine in Mexico was experiencing lengthy downtimes and using high volumes of water for lubricating pump packing.
Major savings with CKD double seal
The single seals being used by Swedish water treatment company were unsuitable for the job they were being asked to do, allowing limescale to enter between the seal faces and leak out on to the floor of the plant.
Seal upgrades save over US $3.4million in seven years
A company in the Oil and Gas industry in Qatar were dissatisfied with the reliability of the mechanical seal used in crude export and oil/water booster pumps.
Mining company saves $8 million AUD with AESSEAL system
A coal mine in Australia was having seal failures roughly every two weeks on two disposal pumps.
Safety and reliability with AESSEAL heavy duty seal
A mining company in Australia was facing persistent problems from seal failures on one of its slurry pumps.
Mining company saves $8 million AUD with AESSEAL system
A coal mine in Australia was having seal failures roughly every two weeks on two disposal pumps.
DMSF makes its mark in Japanese paper industry
The installation of an AESSEAL® DMSF™ seal at a Japanese paper plant has increased the MTBF from just six months to seven years.
Improved Safety and Reliability
A major manufacturer in the UK were having reliability issues with the seal on a critical Labour chemical pump used to pump caustic solution.
Warman conversion the answer for Spanish company
A seal conversion kit for the Warman® AH Range of Ultra Heavy Duty Slurry Pumps helped to solve a variety of problems being experienced by a Spanish aluminium producer.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
Major savings with CKD double seal
The single seals being used by Swedish water treatment company were unsuitable for the job they were being asked to do, allowing limescale to enter between the seal faces and leak out on to the floor of the plant.
FIDC ends costly leaks at US firm
The installation of an FIDC seal to replace single seals with no flush or API Plan has dramatically improved pump reliability at a pulp and paper company in New England.
Staying cool in Cardiff
The cooling system in a High Profile office building in the Cardiff Bay area was operating with just a single duty pump and no standby.
Fantastic seal life for notoriously difficult application
A pulp & paper company in the Canada were dissatisfied with the reliability of the mechanical seal used in its Chlorine Dioxide generator pump.
Warman conversion the answer for Spanish company
A seal conversion kit for the Warman® AH Range of Ultra Heavy Duty Slurry Pumps helped to solve a variety of problems being experienced by a Spanish aluminium producer.
Warman conversion the answer for Spanish company
A seal conversion kit for the Warman® AH Range of Ultra Heavy Duty Slurry Pumps helped to solve a variety of problems being experienced by a Spanish aluminium producer.
Seal upgrades save over US $3.4million in seven years
A company in the Oil and Gas industry in Qatar were dissatisfied with the reliability of the mechanical seal used in crude export and oil/water booster pumps.
AESSEAL help a Polyethylene plant save €144,000 in 30 months
Replacing labyrinth seals with MagTecta on 8 lobe blowers increases MTBF to over 400%.
Staying cool in Cardiff
The cooling system in a High Profile office building in the Cardiff Bay area was operating with just a single duty pump and no standby.
AESSEAL product stops hot oil pump leakage
A large oil and gas company in north Africa contacted AESSEAL to look at a sealing issue on its hot oil pumps.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
AESSEAL system fixes sewage problems for US township
A municipality in Pennsylvania was having issues with major inefficiencies in its sewage treatment system.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
Improved reliability for new process
A refinery in Canada were commissioning a new lipids coprocessing initiative where renewable feedstock is injected into the cracker.
Annual savings of over $2.6 million
A food and beverage customer was experiencing high leakage and contamination in their process fluid on the single pass flow through system they were operating.
ROI In Less Than A Month
a French cardboard manufacturer was experiencing seal failures every two months. AESSEAL worked closely with the customer to find the right solution.
DMSF makes its mark in Japanese paper industry
The installation of an AESSEAL® DMSF™ seal at a Japanese paper plant has increased the MTBF from just six months to seven years.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
Chemical plant saved over €500,000 in the first year
A critical glue agitator vessel was affecting productivity for a silicone manufacturing facility in France. This situation was costing the company thousands of Euros in lost production.
Fantastic seal life for notoriously difficult application
A pulp & paper company in the Canada were dissatisfied with the reliability of the mechanical seal used in its Chlorine Dioxide generator pump.
Improved reliability for new process
A refinery in Canada were commissioning a new lipids coprocessing initiative where renewable feedstock is injected into the cracker.
Staying cool in Cardiff
The cooling system in a High Profile office building in the Cardiff Bay area was operating with just a single duty pump and no standby.
DMSF seal the answer at South African plant
The installation of the AESSEAL DMSF seal and SW2 water management system at the Ford plant in Pretoria, South Africa, has improved the MTBF of a crucial seal from less than two weeks to more than two years.
DMSC saves Nestlé Purina £182k in just 10 months
Significant savings with mechanical seal and bearing protection for the pet food manufacturer
DMSF solves reliability issues for Swedish company
Elastomer degradation was causing the seals on three of the boiler feed pumps at a Swedish energy plant to fail around every 12 months.
DMSC saves Nestlé Purina £182k in just 10 months
Significant savings with mechanical seal and bearing protection for the pet food manufacturer
Major savings for Algerian food producer
A food production plant in Algeria is saving an estimated $225,000 a year following the installation of an AESSEAL LabTecta OP bearing protector.
AESSEAL upgrade removes safety risk
A sealant being used on an Sulzer APP3 pump by a Spanish biofuel company was leaking each time the pump was stopped.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
Improved reliability for new process
A refinery in Canada were commissioning a new lipids coprocessing initiative where renewable feedstock is injected into the cracker.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
Staying cool in Cardiff
The cooling system in a High Profile office building in the Cardiff Bay area was operating with just a single duty pump and no standby.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
Improved reliability for new process
A refinery in Canada were commissioning a new lipids coprocessing initiative where renewable feedstock is injected into the cracker.
CDPH & EasyClean boosts MTBF from four months to seven years
The installation of a CDPH double mechanical seal along with an EasyClean™ seal support system proved to be the remedy for the frequent failures of a competitor’s seal at a power plant in Denmark.
Improved Safety and Reliability
A major manufacturer in the UK were having reliability issues with the seal on a critical Labour chemical pump used to pump caustic solution.
Bitumen pump upgrade saves over £23,000 a year
Asphalt producer pump for road surfaces was gland packed and losing over 15 tonnes of bitumen.
Major savings for Algerian food producer
A food production plant in Algeria is saving an estimated $225,000 a year following the installation of an AESSEAL LabTecta OP bearing protector.
Warman conversion the answer for Spanish company
A seal conversion kit for the Warman® AH Range of Ultra Heavy Duty Slurry Pumps helped to solve a variety of problems being experienced by a Spanish aluminium producer.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
LabTecta saves €360,000 for Spanish company each year
A lip seal which was leaking oil from an extruder gearbox was causing persistent problems for a Spanish petrochemical company.
Improved reliability for new process
A refinery in Canada were commissioning a new lipids coprocessing initiative where renewable feedstock is injected into the cracker.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
Chemical plant saved over €500,000 in the first year
A critical glue agitator vessel was affecting productivity for a silicone manufacturing facility in France. This situation was costing the company thousands of Euros in lost production.
Chemical plant saved over €500,000 in the first year
A critical glue agitator vessel was affecting productivity for a silicone manufacturing facility in France. This situation was costing the company thousands of Euros in lost production.
Prompt delivery saves three-month delay
A 12-week delay on the commissioning of a new oil and gas plant in Kuwait was avoided when AESSEAL was able to step in to replace a defective competitor’s seal at short notice.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
Leakage problem solved with STS
A global energy company was facing significant losses as a result of damage to the steam turbine housing at one of its ethylene plants.
Bitumen pump upgrade saves over £23,000 a year
Asphalt producer pump for road surfaces was gland packed and losing over 15 tonnes of bitumen.
Warman conversion the answer for Spanish company
A seal conversion kit for the Warman® AH Range of Ultra Heavy Duty Slurry Pumps helped to solve a variety of problems being experienced by a Spanish aluminium producer.
Improved Safety and Reliability
A major manufacturer in the UK were having reliability issues with the seal on a critical Labour chemical pump used to pump caustic solution.
Chemical Producer Saves Over £1.7 Million in Plant Downtime
A specialty chemical company at its UK processing facility were desperately trying to get spare parts for the mechanical seal on one of its critical reactors.
Major savings follow installation of AESSEAL product
A petrochemical company based in the Middle East was having problems with persistent and costly seal failures.
Major savings follow installation of AESSEAL product
A petrochemical company based in the Middle East was having problems with persistent and costly seal failures.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
Major savings for Algerian food producer
A food production plant in Algeria is saving an estimated $225,000 a year following the installation of an AESSEAL LabTecta OP bearing protector.
Safety and reliability with AESSEAL heavy duty seal
A mining company in Australia was facing persistent problems from seal failures on one of its slurry pumps.
Improved Safety and Reliability
A major manufacturer in the UK were having reliability issues with the seal on a critical Labour chemical pump used to pump caustic solution.
DMSC saves Nestlé Purina £182k in just 10 months
Significant savings with mechanical seal and bearing protection for the pet food manufacturer
DMSC saves Nestlé Purina £182k in just 10 months
Significant savings with mechanical seal and bearing protection for the pet food manufacturer
AES-Elast the answer to seal selection problem
Employees at William Grant’s Scottish whisky distillery in Girvan, Ayshire, were having difficulty selecting the correct mechanical seals for specific applications.
Seal upgrades save over US $3.4million in seven years
A company in the Oil and Gas industry in Qatar were dissatisfied with the reliability of the mechanical seal used in crude export and oil/water booster pumps.
ROI In Less Than A Month
a French cardboard manufacturer was experiencing seal failures every two months. AESSEAL worked closely with the customer to find the right solution.
CDPH & EasyClean boosts MTBF from four months to seven years
The installation of a CDPH double mechanical seal along with an EasyClean™ seal support system proved to be the remedy for the frequent failures of a competitor’s seal at a power plant in Denmark.
Staying cool in Cardiff
The cooling system in a High Profile office building in the Cardiff Bay area was operating with just a single duty pump and no standby.
Mechanical seals runs an incredible 17 years without problems
Tongaat Hullett Sugar were un happy with the amount of maintenance required on the sealing of one of its pumps.
Improved reliability for new process
A refinery in Canada were commissioning a new lipids coprocessing initiative where renewable feedstock is injected into the cracker.
DMSF seal the answer at South African plant
The installation of the AESSEAL DMSF seal and SW2 water management system at the Ford plant in Pretoria, South Africa, has improved the MTBF of a crucial seal from less than two weeks to more than two years.
AES-Elast the answer to seal selection problem
Employees at William Grant’s Scottish whisky distillery in Girvan, Ayshire, were having difficulty selecting the correct mechanical seals for specific applications.
Warman conversion the answer for Spanish company
A seal conversion kit for the Warman® AH Range of Ultra Heavy Duty Slurry Pumps helped to solve a variety of problems being experienced by a Spanish aluminium producer.
CDPH & EasyClean boosts MTBF from four months to seven years
The installation of a CDPH double mechanical seal along with an EasyClean™ seal support system proved to be the remedy for the frequent failures of a competitor’s seal at a power plant in Denmark.
DMSF seal the answer at South African plant
The installation of the AESSEAL DMSF seal and SW2 water management system at the Ford plant in Pretoria, South Africa, has improved the MTBF of a crucial seal from less than two weeks to more than two years.
Improved Safety and Reliability
A major manufacturer in the UK were having reliability issues with the seal on a critical Labour chemical pump used to pump caustic solution.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
Safety and reliability with AESSEAL heavy duty seal
A mining company in Australia was facing persistent problems from seal failures on one of its slurry pumps.
Mining company saves $8 million AUD with AESSEAL system
A coal mine in Australia was having seal failures roughly every two weeks on two disposal pumps.
Staying cool in Cardiff
The cooling system in a High Profile office building in the Cardiff Bay area was operating with just a single duty pump and no standby.
Major savings follow installation of AESSEAL product
A petrochemical company based in the Middle East was having problems with persistent and costly seal failures.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
LabTecta saves €360,000 for Spanish company each year
A lip seal which was leaking oil from an extruder gearbox was causing persistent problems for a Spanish petrochemical company.
CDPH & EasyClean boosts MTBF from four months to seven years
The installation of a CDPH double mechanical seal along with an EasyClean™ seal support system proved to be the remedy for the frequent failures of a competitor’s seal at a power plant in Denmark.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
Fantastic seal life for notoriously difficult application
A pulp & paper company in the Canada were dissatisfied with the reliability of the mechanical seal used in its Chlorine Dioxide generator pump.
ROI In Less Than A Month
a French cardboard manufacturer was experiencing seal failures every two months. AESSEAL worked closely with the customer to find the right solution.
DMSF solves reliability issues for Swedish company
Elastomer degradation was causing the seals on three of the boiler feed pumps at a Swedish energy plant to fail around every 12 months.
Change to packing saves Swiss company $millions
A chocolate producer in Switzerland has saved around ₣2.3 million ($2.6 million) over the past year following its decision to change to an AESSEAL pump packing system.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
Chemical plant saved over €500,000 in the first year
A critical glue agitator vessel was affecting productivity for a silicone manufacturing facility in France. This situation was costing the company thousands of Euros in lost production.
Chemical plant saved over €500,000 in the first year
A critical glue agitator vessel was affecting productivity for a silicone manufacturing facility in France. This situation was costing the company thousands of Euros in lost production.
Prompt delivery saves three-month delay
A 12-week delay on the commissioning of a new oil and gas plant in Kuwait was avoided when AESSEAL was able to step in to replace a defective competitor’s seal at short notice.
Mining company saves $8 million AUD with AESSEAL system
A coal mine in Australia was having seal failures roughly every two weeks on two disposal pumps.
DMSF seal the answer at South African plant
The installation of the AESSEAL DMSF seal and SW2 water management system at the Ford plant in Pretoria, South Africa, has improved the MTBF of a crucial seal from less than two weeks to more than two years.
Staying cool in Cardiff
The cooling system in a High Profile office building in the Cardiff Bay area was operating with just a single duty pump and no standby.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
AESSEAL help a Polyethylene plant save €144,000 in 30 months
Replacing labyrinth seals with MagTecta on 8 lobe blowers increases MTBF to over 400%.
DMSF makes its mark in Japanese paper industry
The installation of an AESSEAL® DMSF™ seal at a Japanese paper plant has increased the MTBF from just six months to seven years.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
ROI In Less Than A Month
a French cardboard manufacturer was experiencing seal failures every two months. AESSEAL worked closely with the customer to find the right solution.
AESSEAL product stops hot oil pump leakage
A large oil and gas company in north Africa contacted AESSEAL to look at a sealing issue on its hot oil pumps.
AESSEAL helps UK firm to multi-million pound savings
A leading UK company is set to save more than £5 million over five years following the installation of AESSEAL LabTecta OP bearing protectors.
Safety and reliability with AESSEAL heavy duty seal
A mining company in Australia was facing persistent problems from seal failures on one of its slurry pumps.
Mechanical seals runs an incredible 17 years without problems
Tongaat Hullett Sugar were un happy with the amount of maintenance required on the sealing of one of its pumps.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
AESSEAL solves reliability problem for US paper company
The installation of the AESSEAL DMSC double mechanical seal, a close clearance bushing, a FLOWTRUE flowmeter, and a 25 litre SW2 water management system, has solved a problem of repeated seal failure for a US paper company.
AESSEAL product stops hot oil pump leakage
A large oil and gas company in north Africa contacted AESSEAL to look at a sealing issue on its hot oil pumps.
AESSEAL upgrade removes safety risk
A sealant being used on an Sulzer APP3 pump by a Spanish biofuel company was leaking each time the pump was stopped.
Bitumen pump upgrade saves over £23,000 a year
Asphalt producer pump for road surfaces was gland packed and losing over 15 tonnes of bitumen.
AESSEAL system fixes sewage problems for US township
A municipality in Pennsylvania was having issues with major inefficiencies in its sewage treatment system.
Bitumen pump upgrade saves over £23,000 a year
Asphalt producer pump for road surfaces was gland packed and losing over 15 tonnes of bitumen.
DMSF makes its mark in Japanese paper industry
The installation of an AESSEAL® DMSF™ seal at a Japanese paper plant has increased the MTBF from just six months to seven years.
Major savings for Algerian food producer
A food production plant in Algeria is saving an estimated $225,000 a year following the installation of an AESSEAL LabTecta OP bearing protector.
Major savings follow installation of AESSEAL product
A petrochemical company based in the Middle East was having problems with persistent and costly seal failures.
Fantastic seal life for notoriously difficult application
A pulp & paper company in the Canada were dissatisfied with the reliability of the mechanical seal used in its Chlorine Dioxide generator pump.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
AESSEAL system fixes sewage problems for US township
A municipality in Pennsylvania was having issues with major inefficiencies in its sewage treatment system.
AES-Elast the answer to seal selection problem
Employees at William Grant’s Scottish whisky distillery in Girvan, Ayshire, were having difficulty selecting the correct mechanical seals for specific applications.
DMSF seals end contamination problem for Spanish firm
A metalworking company in northern Spain had equipped its pumps with component mechanical seals, parallel spring-mounted back-to-back, with an API Plan 54 circulation system.
AES-Elast the answer to seal selection problem
Employees at William Grant’s Scottish whisky distillery in Girvan, Ayshire, were having difficulty selecting the correct mechanical seals for specific applications.
CDPH & EasyClean boosts MTBF from four months to seven years
The installation of a CDPH double mechanical seal along with an EasyClean™ seal support system proved to be the remedy for the frequent failures of a competitor’s seal at a power plant in Denmark.
Navy reduces repair times and improves pump reliability
When a seal failed, divers had to fit blanks to the pump inlets below the waterline before it was possible to carry out a repair.
DMSF solves reliability issues for Swedish company
Elastomer degradation was causing the seals on three of the boiler feed pumps at a Swedish energy plant to fail around every 12 months.
Dangerous oil leak problem solved by LabTecta FS
A silicon lip seal fitted to a rubber lumps reactor at a chemical plant in northern Spain failed after just ten days, resulting in the serious leakage of oil from the gearbox.
